Methenolone Enanthate

Methenolone Enanthate, also known by its brand name Primobolan Depot, is a long-acting anabolic steroid. It is derived from dihydrotestosterone (DHT) and is primarily used to promote muscle growth, enhance athletic performance, and aid in the preservation of lean muscle mass during cutting cycles. Here are some key points about Methenolone Enanthate:

Characteristics of Methenolone Enanthate

1. Anabolic Properties: Methenolone Enanthate has strong anabolic effects, which means it promotes significant muscle growth. It is effective in building lean, high-quality muscle tissue without causing excessive water retention.
2. Mild Androgenic Effects: Compared to many other anabolic steroids, Methenolone Enanthate has a low androgenic rating. This translates to fewer side effects related to male characteristics, such as acne, hair loss, and deepening of the voice.
3. Injectable Form: Methenolone Enanthate is typically administered via injection. The enanthate ester attached to the methenolone molecule allows for a slow and steady release of the hormone into the bloodstream, which means less frequent injections are needed compared to oral steroids.
4. Cutting Cycles: This steroid is often favored during cutting cycles because it helps preserve muscle mass while promoting fat loss. Users can achieve a more defined and shredded physique without losing muscle.
5. Performance Enhancement: Athletes and bodybuilders use Methenolone Enanthate to enhance their performance. It increases strength and endurance, allowing for more intense and prolonged workouts.

For optimal results, it is important to follow the recommended dosage and cycle guidelines for Methenolone Enanthate:

• Beginner Users: A common starting dosage for men is 400mg per week, while women should start with 50-100mg per week.
• Intermediate Users: Men can increase their dosage to 600mg per week, and women can take up to 100-150mg per week.
• Advanced Users: Experienced users may take up to 800mg per week, but it is crucial to monitor the body’s response closely.

Cycle Duration: Typical cycles last between 8-12 weeks, depending on individual goals and tolerance levels.

Creating a homebrew recipe for Primobolan (Methenolone Enanthate) at a concentration of 100mg/ml requires precise measurement and sterile techniques to ensure safety and efficacy. This process involves dissolving the active ingredient in a carrier oil, along with solvents and a preservative. Here’s a basic recipe:

Ingredients and Equipment

Ingredients:

1. Methenolone Enanthate powder
2. Benzyl Alcohol (BA) - used as a preservative
3. Benzyl Benzoate (BB) - used as a solvent
4. Carrier oil (e.g., Grapeseed oil or another sterile oil suitable for injection)

Equipment:

1. Sterile vials
2. Syringes and needles
3. Milligram scale (for accurate measurement)
4. Sterile mixing container
5. Sterile filters (e.g., Whatman sterile syringe filters)
6. Alcohol wipes (for sterilizing surfaces and equipment)
7. Crimper (for sealing vials if necessary)

Recipe for 100ml at 100mg/ml Concentration

Ingredients:

• 10 grams of Methenolone Enanthate powder
• 2 ml of Benzyl Alcohol (2%)
• 20 ml of Benzyl Benzoate (20%)
• 68 ml of Carrier Oil (Grapeseed oil or other sterile oil)

Steps

1. Preparation:
   • Ensure all equipment and surfaces are thoroughly sterilized.
   • Wear sterile gloves and work in a clean environment to prevent contamination.
2. Weigh the Powder:
   • Accurately weigh 10 grams of Methenolone Enanthate powder using a milligram scale.
3. Mix Solvents and Powder:
   • In a sterile mixing container, add the 10 grams of Methenolone Enanthate powder.
   • Add 2 ml of Benzyl Alcohol and 20 ml of Benzyl Benzoate to the powder.
   • Mix thoroughly until the powder is fully dissolved.
4. Add Carrier Oil:
   • Slowly add the carrier oil (68 ml) to the solution while stirring continuously.
   • Ensure the solution is well mixed and homogenous.
5. Heat the Solution:
   • Warm the solution slightly (not boiling) to ensure all ingredients are fully dissolved and well mixed. This can be done using a water bath. Ensure the temperature does not exceed 50-60°C.
6. Filtering:
   • Draw the solution into a sterile syringe and attach a sterile Whatman syringe filter.
   • Filter the solution into sterile vials to remove any impurities or undissolved particles.
7. Sealing the Vials:
   • If using crimp-top vials, use a crimper to seal the vials properly.
   • Ensure the vials are properly labeled with the content and concentration.
8. Storage:
   • Store the finished product in a cool, dark place to maintain its potency and shelf life.